12.5. Doors

Door upholstery
Switch off ignition and disconnect a wire from the negative plug of the rechargeable battery.

Fig. 12.7. Forward door: 1 – external decorative slip; 2 – molding; 3 – forward door; 4 – sealant; 5 – glass sealant; 6 – glass; 7 – window regulator; 8 – armrest; 9 – external handle of a door; 10 – persistent ring; 11 – ring; 12 – window regulator handle; 13 – shock plate; 14 – door lock; 15 – internal handle of a door; 16 – door lock cylinder; 17 – door upholstery; 18 – limiter of opening of a door; 19 – limiter pin


Fig. 12.8. Back door: 1 – molding; 2 – back door; 3 – sealant; 4 – glass sealant; 5 – central rack; 6 – sealant of a triangular window leaf of salon; 7 – glass; 8 – triangular window leaf of salon; 9 – the support flew down; 10 – window regulator; 11 – persistent ring; 12 – ring; 13 – window regulator handle; 14 – shock plate; 15 – door lock; 16 – internal handle of a door; 17 – external handle of a door; 18 – armrest; 19 – door upholstery;
20 – limiter of opening of a door; 21 – limiter pin


Remove the window regulator drive handle (a window with the manual drive) or the switch (a window with the electric drive) (fig. 12.7, 12.8). The persistent ring which fixes the window regulator handle is released if to place pure fabric between the handle and an upholstery of a door and, stretching fabric opposite to the ends of a persistent ring, to hook on a persistent ring and to release it. At the same time it is necessary to pull the handle on itself that she after release of a persistent ring acted from shliyets of a window regulator.
Uncover the internal handle of a door.
Unscrew lock screws of fastening of an armrest.
Using the screw-driver with a wide edge, on perimeter disconnect clamps and separate a door upholstery from a door. Clamps are established very densely therefore care is necessary not to break them during removal.
Remove a door upholstery, having disconnected it from the handle of the lock of a door and moving up.
Carefully remove the film protecting a door from water hit.
Installation is carried out to the sequences, the return to removal, taking into account the following.
Carefully establish the film protecting a door from water hit in initial situation, having established it without folds and gaps.
Before installation check and if necessary replace clamps which were broken at removal of an upholstery of a door.
At installation of an upholstery of a door arrange upholstery top over the handle of the lock of a door and press it before installation into place.
Sharply pressing an upholstery in the locations of clamps, fix an upholstery on a door.
Elements of fastening of an upholstery
The plastic connector reminding the self-cutting screw is widely used for fastening of various elements of an upholstery. In spite of the fact that this connector carries out a screw role, actually it is a combination of the self-cutting screw and a clamp. The cutting basis of a connector extends when in it screw in the screw.
To remove a connector, hold its basis with fingers and turn out the screw by means of the crosswise screw-driver, and then the flat screw-driver get the basis.
To insert a connector, establish the basis in necessary situation and the screw-driver screw in it the screw.

External handle of a door
Lift glass up to an emphasis.
Remove an upholstery of a door and a water protective film.

Fig. 12.9. Use of the flat screw-driver for a draft detachment from the external handle of a door


The flat screw-driver disconnect draft from the external handle of a door (fig. 12.9).
Turn out bolts and remove the external handle of a door. Disconnect the socket from the door handle switch (if it is established).
Installation is carried out to the sequences, the return to removal.

External rear-view mirror
On models with power windows disconnect a wire from the negative plug of the rechargeable battery.

Fig. 12.10. Elements of fastening of an external rear-view mirror: 1 – decorative slip; 2 – screw; 3 – mirror


Remove a decorative slip (fig. 12.10).
On models with power windows disconnect the electric socket from a mirror.
Turn out screws and remove a mirror.
Installation is carried out to the sequences, the return to removal.
Glasses and window regulators
Lower door glass, remove an upholstery of a door and a water protective film.
On models with power windows disconnect a wire from the negative plug of the rechargeable battery.
On back doors remove tape laying.

Fig. 12.11. An arrangement of bolts of fastening of glass to a window regulator


Move a window regulator to such situation that bolts of fastening of glass to a window regulator were available through technological openings in the internal panel of a door (fig. 12.11). Turn out bolts.
On models with power windows disconnect the socket from the window regulator engine.
On forward doors turn out bolts and extract glass.

Fig. 12.12. Removal of the central rack from a back door


On back doors turn out the screw and a bolt, remove the central rack (fig. 12.12). Incline a back part of glass down, remove a glass support from a guide and then, moving up, extract glass from a door.

Fig. 12.13. Removal of a window regulator from a forward door


On forward and back doors turn out bolts and take a window regulator through technological openings in the internal panel of a door (fig. 12.13).
On models with power windows turn off bolts and remove the engine from a window regulator.

PREVENTION
Be very careful during removal of the engine as the spring returning a window regulator stopper in the top situation will be released.

Installation is carried out to the sequences, the return to removal, taking into account the following.

Fig. 12.14. Installation of glass of a triangular window leaf


For simplification of installation of glass of a triangular window leaf grease a glass frame with soap solution (fig. 12.14).
On models with power windows connect a wire to the negative plug of the rechargeable battery and before installation of glass lower a window regulator in the lower situation.
After completion of installation check work of a window regulator, having several times lifted and having lowered glass to be sure that it moves easily and freely. If it is necessary, weaken bolts and adjust the provision of a window regulator.

Removal, installation and adjustment of provision of a door
Removal
On models with power windows disconnect a wire from the negative plug of the rechargeable battery. Disconnect the contact socket of a plait of wires of a door. For access to the socket can be required to remove previously an upholstery of a door or adjacent panels of a body.

Fig. 12.15. Arrangement of bolts of fastening of a loop of a door


Mark with a marker the provision of bolts of fastening of loops of a door (fig. 12.15). Remove the limiter of opening of a door.
Open a door and support it by supports or jacks, having laid between them and a door pure rags.
Ask the assistant to support a door. Turn off bolts of fastening of loops from doors or from a rack and remove a door.
Installation
Installation is carried out to the sequences, the return to removal. Fix a pylevlagozashchitny film (if she acted), having established it without folds and gaps. The surface on which the pylevlagozashchitny film is pasted has to be ideally pure.
If installation of earlier removed door is carried out, combine earlier put tags.
Adjustment of provision of a door
Check a condition of loops of a door for what open a door and lift it up, without lifting a body.
After installation of a door check that the gap on perimeter of a door was identical everywhere, and the external surface of a door was flush with other elements of a body. For adjustment of a gap on perimeter of a door weaken bolts of fastening of hinges of a door to a door and, moving a door, adjust its situation then tighten fastening bolts.

Fig. 12.16. The directions of movement of a shock plate of the lock of a door for adjustment of provision of a back part of a door


In the last turn weaken bolts and adjust the provision of a shock plate of the lock of a door so that a back part of a door was flush with a back door or elements of a body (fig. 12.16).