13.7. Replacement of lamps

Before replacement of a lamp of external lighting disconnect a wire from the negative plug of the rechargeable battery. Keep in mind that if the lamp just burned, it can be too hot.
Previously check the corresponding electric chain and a safety lock. Do not concern a glass flask of a lamp barehanded. Fatty traces on a lamp lead to its darkening and bystry failure. Surely replace the failed lamps with lamps of the same type. Wipe the spots arising on imprudence with a pure lint-free rag or alcohol.
The lamps applied on the car are given in tab. 13.1.

Table 13.1
The applied lamps

Forward indexes of turn and dimensional lighting

Fig. 13.32. Forward indexes of turn and dimensional lighting: 1 – lens of forward side dimensional lighting; 2 – lamp of forward side dimensional lighting; 3 – lamp of the lens of the index of turn; 4 – lens of the index of turn


Lamps of forward indexes of turn and dimensional lighting can be replaced after a reversing of screws and removal of lenses (fig. 13.32). Take out a lamp from the boss (side dimensional lighting) or press a lamp and turn it counterclockwise (indexes of turn).
Establish a new lamp, check its work then establish the lens.

Headlight with the replaced lamp
Open a cowl. Disconnect the socket from a headlight and remove a rubber cover.
Wring out a spring clip and take a lamp.
Do not concern a glass flask of a lamp barehanded. Fatty traces on a lamp lead to darkening of a flask and a bystry exit of a lamp out of operation. If there were fatty spots, wipe them with a pure lint-free rag or alcohol.
Establish a new lamp, having inserted ledges on a lamp socle into deepenings in a reflector, and fix it by means of a spring clip.
Establish a rubber cover by a tag of "TORAHS" up and connect the socket. Check work of headlights then close a cowl.

Lighting lamps of salon
 Ignition switch illumination lamp
For access to the switch of ignition remove casings of a steering column. Take a lamp from a nest and establish into place new. Establish casings of a steering column.
Plafond of illumination of salon

Fig. 13.33. Replacement of a lamp (1) of a plafond of illumination of salon


Undertake for the lens, pull him down and remove. Take a lamp from a nest and establish into place new (fig. 13.33). Check work of a lamp and establish the lens.
Lamp for reading cards

Fig. 13.34. Replacement of a lamp of a plafond of illumination of salon / for reading cards


The screw-driver remove the inclusion lens/button. Extend a lamp from a nest and establish into place new (fig. 13.34). Check whether the lamp burns, and establish the lens.
Lamps of illumination of a combination of devices
Lamps of illumination of a combination of devices can be replaced only after removal of a combination of devices.
Turn a cartridge with a lamp, remove it from a combination of devices and take a lamp from the boss. Some lamps are not taken out from the boss therefore they should be replaced together with the boss.
Installation is carried out to the sequences, the return to removal.
Radio receiver illumination lamps
Lamps of illumination of the radio receiver are screwed in cartridges, they can be replaced after removal of the radio receiver.
Lamps of illumination of the control panel of a heater
Remove the control panel of a heater. For ensuring access to lamps it is necessary to disconnect several cables of management of a heater.
Take a lamp from the boss and establish into place new. Check its work then install the control panel of a heater.
Lighting lamp of a ware box
For ensuring access to a lamp turn out four screws and remove a ware box.
Take a lamp from the boss and establish new. Check its work then establish a ware box into place.
Lamps of illumination of switches of the dashboard
Remove facing of the dashboard near glass of a combination of devices and disconnect a cartridge and a lamp.
Replace a lamp, check whether it burns, then establish into place a cartridge and facing.
Floor illumination lamps
Remove facing in the lower part of the dashboard, remove a lamp and a cartridge from the panel.
Replace a lamp and check its work. Install a cartridge in the panel then establish facing.
Luggage carrier lighting lamps

Fig. 13.35. Lamps of illumination of registration plate and luggage carrier: and – for cars with bodies the sedan and a compartment; b – for cars with a body the hatchback; 1 – switch; 2 – lamp and boss of a lamp of illumination of a luggage carrier; 3 – lens of a lamp of illumination of a luggage carrier; 4 – lens of a lamp of illumination of registration plate; 5 – lamp of a lamp of illumination of registration plate


Remove the lens, take a lamp from the boss (fig. 13.35).
Establish a new lamp, check its work then establish the lens.

Lamps of external lighting
Lighting lamps of registration plate
For access to a lamp unscrew screws and remove the lens of a lamp of illumination of registration plate (see fig. 13.35). Establish a new lamp, check whether it then establish the lens burns.
Lamps of back lamps
Remove an internal upholstery of a luggage carrier.

Fig. 13.36. Back lamp: and – for cars with bodies the sedan and a compartment; b – for cars with a body the hatchback


For access to lamps of a stoplight, light of a backing, back dimensional and parking lighting squeeze uvulas and remove a casing from a back lamp (fig. 13.36). Replace a lamp. At installation check that uvulas were latched and held a casing.
Check work of lamps then establish an internal upholstery of a luggage carrier.

Replacement of the lens of a back lamp
Remove a back lamp.
Turn off the nuts fixing the lens (four nuts on cars the sedan and a compartment or seven nuts on cars the hatchback). Remove the lens and consolidation.
Lenses it is possible to remove after a softening of the glue holding them on the place by means of the hair dryer or the compressor of supply of hot air.
Establish new lenses. If it is possible, use old glue, it and having pressed heating the lens into place. If reuse of old glue was insufficient, apply new glue in grooves in the case of lenses.
Check the new block of lenses for tightness, having put it in water.
Installation is carried out to the sequences, the return to removal.